ACROBOTIC Temperature, Humidity, Pressure and Gas Sensor Breakout Board for Arduino Raspberry Pi ESP8266 BME-680 3~5VDC BME680
Huge Savings Item! Save 13% on the ACROBOTIC Temperature, Humidity, Pressure and Gas Sensor Breakout Board for Arduino Raspberry Pi ESP8266 BME-680 3~5VDC BME680 by ACROBOTIC at In The National Interest. MPN: BRK-00019. Hurry! Limited time offer. Offer valid only while supplies last. This breakout board provides a convenient way to start using the popular BME680, a Temperature, Humidity, Pressure and VOC Gas Sensor Module. The BME680 is a low-power sensor that detects with high linearity and accuracy temperature, humidity, barometric pressure, and VOC gas. It includes both SPI and I2C interfaces for reading the measured values using our preferred microcontrollers (e.g., Arduino, ESP8266) and single-board computers (e.g., Raspberry Pi). This high-precision sensor can
Product Description & Reviews
This breakout board provides a convenient way to start using the popular BME680, a Temperature, Humidity, Pressure and VOC Gas Sensor Module. The BME680 is a low-power sensor that detects with high linearity and accuracy temperature, humidity, barometric pressure, and VOC gas. It includes both SPI and I2C interfaces for reading the measured values using our preferred microcontrollers (e.g., Arduino, ESP8266) and single-board computers (e.g., Raspberry Pi). This high-precision sensor can measure humidity with ±3% accuracy, barometric pressure with ±1 hPa absolute accuracy, and temperature with ±1.0°C accuracy. Because of the accuracy in pressure, the sensor can be used to estimate altitude within ±1 meter! The gas sensor works is by changes in its internal resistance, which is designed to be sensitive to changes in concentration of Volatile Organic Compound (VOC) gases. Although the sensor works great, it should not be used for any safety, medical or finished product usage. All gas sensors require calibration for precision output. Features: Power Supply: 5VDC This breakout PCB facilitates using the BME680 sensor, specially on solderless breadboards! Sturdy (1.6mm), purple PCB with a 6-pin header on on side (VCC, GND, SDA/SDI, SCL/SCK, SDO, and CS) 6-Pin header included (soldering needed!) We have written useful guides for getting you started with the BME680: ESP8266: http://learn.acrobotic.com/tutorials/
Features & Highlights
- Measure changes in Temperature, Humidity, Pressure and VOC Gas
- Simply supply power and connect the digital communication pins (I2C or SPI) to your Arduino, ESP8266, Raspberry Pi, etc.
- Operating voltage of 3~5VDC
- Easy to use on a breadboard with the included 6-pin header
- Perfect for DIY Weather Stations and Air Quality Monitors
|Item Weight:||0.01 pounds|
|Item Size:||0.66 x 0.2 x 0.2 inches|
|Package Weight:||0.71 pounds|
|Package Size:||3.3 x 0.2 x 0.2 inches|
Have questions about this item, or would like to inquire about a custom or bulk order?
If you have any questions about this product by ACROBOTIC, contact us by completing and submitting the form below. If you are looking for a specif part number, please include it with your message.
Related Best Sellers
mpn: CQ200A1004, ean: 0085267878791,
Honeywell 750 Millivolt Replacement Thermopile Generators have long been used in self-powered heaters and hot water equipment. The Honeywell CQ200A has been proven in millions of appliances as the contractor's preferred thermopile and are found in many of today's self powered gas fireplaces.750 millivolt output gas pilot safety control. 35 in. lead length for self-generating pilot systems. Features a push-in clip for easy pilot burner installation. Compatible with the majority of millivolt gas
mpn: DK2.5N-WE, ean: 0737123111169,
Dinkle DK2.5N-WE white color block has a compact design that saves wiring space. The high reliability and robust design adapts vibration and harsh thermal variation to prevent terminal connection fault. Rated voltage: UL 600V, IEC 1,000 V. Rated current: UL 20A, IEC 24A. Conductor cross-section, solid(AWG/mm2): UL 22-12, IEC 0.5-2.5. Conductor cross-section, flexible(AWG/mm2): UL 22-12, IEC 0.5-2.5. Rated impulse withstand voltage: 6KV. Torque(N-m): 0.4. Screw: M2.5. Wire strip length: 9-11mm.
PT100 MAX31865 RTD Temperature Thermocouple Sensor Amplifier Module For Arduino Description: We've carried various MAXIM thermocouple amplifiers and they're great - but thermocouples don't have the best accuracy or precision, for when the readings must be as good as can be. The MAX31865 handles all of your RTD needs, and can even compensate 3 or 4 wire RTDs for better accuracy. Connect to it with any microcontroller over SPI and read out the resistance ratio from the internal ADC. We put a
By Mr. Heater
mpn: F270320, ean: 0089301703209,
The Mr. Heater 125,000 BTU Forced Air Kerosene Heater. Safe, easy warmth for when the temperature drops. Convert your garage, barn, or tool shed into a year-round workspace! This Mr. Heater Forced Air Kerosene Heater delivers up to 125,000 BTUs of chill-chasing warmth when you're working on your truck, farm equipment, ATV and more. Heats approximately 3,125 sq. ft.. Runs up to 9 hours on a full tank. 8.5-gallon fuel tank. Easy-off access panel and side lift handles. Troubleshooting diagnostics
Parameter Chip: ACS712ELC-5A / ACS712ELC-20A / ACS712ELC-30A Supply Power: 5V Measuring range: 5A / 20A 30A. Analog output: 200 mv/A When there is no the detection current , the output voltage is VCC / 2 PCB board dimension:31x13mm Package Included: 2pcs ACS712 Current Sensor Module DetectorCurrent sensor chips: ACS712ELC-5A / ACS712ELC-20A / ACS712ELC-30A [There are three specifications for the product 5A / 20A /30A. You can choose the specifications according to your needs.];. Pin 5V
PCB terminal is widely used in almost all electronic equipment, such as small eletronic watches, calculators, general computer, communication electronics equipment, etc.Product Name : PCB Terminal Block;Model : 350-3.5. Rated Value : 300V 10A;Poles : 2 Pin. Pitch : 3.5mm/ 0.14'';Dimension : 12 x 7 x 7mm/ 0.47'' x 0.28'' x 0.28'' (L*W*H). Material : Plastic, Electric Parts;Main Color : Green. Net Weight : 43g;Package Content : 50(+/-2%)pcs x PCB Terminal Block.
mpn: 36661, ean: 0646635370806,
Cole Hersee 46210-03 Jumper Terminals ; Category: Junction Blocks ; Manufacturer: Cole Hersee ; Type: Non-Feed Through ; Positions: 1 ; Amps: 250A ; Volts: 6-36V ; Stud Size: 3/8 Inch ; Black Cap To Indicate Negative Connection ; Provides Remote Mounting For Battery Connections Inside Or Outside A Vehicle ; Allows Convenient Jump Start And Charging When Battery Is Not Easily Accessible, Or When Reaching Battery Become Dangerous ; Negative Terminal Can Be Used Individually Or In Conjunction With
VC6934ZZ11, Honeywell, Inc., Tri-State Actuator, Floating, SP3T.
By Automation Systems Interconnect
ASI ASIUK5HESI is a lever actuated 5 x 20 mm fuse holder terminal block without indication. The gray terminal block measures 8.2 mm wide and is rated 12 Amps at 600 Volts. The screw clamp terminations accept 26 to 10 AWG. The lever actuated fuse holder makes fuse insertion and extraction safe and easy. Accessories are SOLD SEPARATELY and include ASIZB810B markers, CT004 (Black) and CT006 (Red) permanent labeling pens, ASIUD1B end Clamp, ASIEBS108 side entry jumpers and PR005-1M standard DIN
By Lind Equipment
This Lind Equipment G12 static ground ball is made of brass for conductivity, and is suitable for grounding applications in aircraft hangars and on tarmacs. It has a 5/8'' ball and a 3/8-16 Unified National Coarse (UNC) stem for compatibility with most ground ball receptacles and grounding clamps with indented jaws. This static ground ball is suitable for use with refueling, tanker, and vacuum trucks and trailers in aviation service.Lind Equipment manufactures portable lighting, portable power,