Tsubaki 35B25FJ Finished Bore Sprocket, Single Strand, Inch, #35 ANSI No., 3/8" Pitch, 25 Teeth, 5/8" Bore
Tsubaki 35B25FJ Finished Bore Sprocket, Single Strand, Inch, #35 ANSI No., 3/8'' Pitch, 25 Teeth, 5/8'' Bore by Tsubaki at In The National Interest. MPN: 35B25FJ. Hurry! Limited time offer. Offer valid only while supplies last. This Tsubaki roller chain sprocket has a 3/8-inch pitch, fits size 35 chains, and is single strand with one set of teeth around its circumference for
This Tsubaki roller chain sprocket has a 3/8-inch pitch, fits size 35 chains, and is single strand with one set of teeth around its circumference for use with single strand chains. It is a Type B sprocket with a hub projection encircling the bore on one side and is ready for installation on a shaft of the appropriate diameter. The teeth of the sprocket help prevent slipping and binding to avoid power loss in assemblies. It meets International Organization for Standardization (ISO) 9001 for quality assurance. This single strand roller chain sprocket is suitable for use in a broad range of applications involving light to moderate loads and ongoing, high-cycle operations, including vehicle transmission systems, construction and agricultural equipment, conveyors, and factory manufacturing and assembly lines, among others.
A roller chain sprocket is a thin wheel with deep, uniformly spaced teeth ringing its circumference. The distance from the peak of one tooth to the next is called the pitch, and is commonly measured in 1/8-inch increments. The sprocket transfers power and motion by a roller chain that is threaded over the teeth of the sprocket. The alignment of the chain with the sprocket's pitch prevents the chain from slipping so that no power is lost. In the center of the sprocket is the bore (hole) for sliding the sprocket onto a shaft, and a bushing or bearing is often fitted to the sprocket’s hub to custom-fit the sprocket onto a shaft to hold it firmly in place. A hub is a protruding, raised lip encircling the bore of the sprocket. Sprockets with hubs on both sides are Type C, sprockets with hubs on one side are Type B, and sprockets with no hubs are Type A sprockets. For applications requiring sprockets to be swapped onto shafts of different diameters, a sprocket with a bore large enough to fit all shafts can be used, with the gap between the bore and shaft closed with a bushing or bearing. Roller chain sprockets are used in a broad range of applications where the drive power of an engine needs to be transferred into motion, such as in motor vehicles, conveyors, escalators, agricultural, forestry and mining equipment, aeronautics, robotics and space exploration, among others.
U.S. Tsubaki Power Transmission manufactures a variety of chains, sprockets, and other power transmission components that meet International Organization for Standardization (ISO) standards for quality assurance. The company, founded in 1917, is headquartered in Wheeling, IL.
Features & Highlights
- Single strand sprocket with one set of teeth around the circumference for applications where a single chain can support the torque and load
- Pitch of 3/8 inch for size 35 chains
- Ready-to-install finished bore with a wide hub on one side
- Type B sprocket with a hub projection on one side to accommodate various types of bushings to help prevent sprocket from slipping on the shaft
- Sprocket teeth help prevent slipping and binding to avoid power loss in assemblies
|Package Weight:||0.9 pounds|
|Package Size:||3.8 x 1.1 x 1.1 inches|
Have questions about this item, or would like to inquire about a custom or bulk order?
If you have any questions about this product by Tsubaki, contact us by completing and submitting the form below. If you are looking for a specif part number, please include it with your message.
Related Best Sellers
mpn: 1, ean: 0663591492489,
# 40 Roller Chain A-Plate Sprocket Sprocket Pitch: 1/2 inches（12.7mm) Number of Teeth: 21 Tooth Bore Diameter: 5/8 inches(15.875mm) Outside Diameter: 3.62 inches(91.948mm) Overall Thick:0.275 inches( 7mm) Material: Carbon SteelMaterial:Carbon Steel...
mpn: 35B30, ean: 0662289158652,
Type "B" Minimum Bore Sprocket. No. 35, 3/8 in. Pitch ANSI Chain. ...
7-1/4" OD, 1-3/8" ID. Universal bolt pattern. Fits Go-Karts & Mini Bikes equipped with Predator 79cc , Predator 212cc or 420cc...
Idler Sprockets: 60 Chain Size, 13 TeethTeeth: 13. Bore: 5/8''. OD: 3.49. ...
mpn: 40BS24H X 3/4, ean: 0888569094667,
TRITAN Finished Bore B-Hub Sprocket features one setscrew over the keyway and a second setscrew at 90 degrees. With high quality carbon steel construction, this sprocket with 1/2 inch pitch has 24 teeth and 3/4 inch finished bore. Sprocket has a blac...
This sprocket has steel teeth and an aluminium inner part. Both sections are permanentely joined by high strength rivets. Stealth sprockets last at least 3 times longer than any other aluminium sprocket whilst it is half the weight of a normal steel ...
mpn: H35B17FL, ean: 0097039296412,
This Tsubaki roller chain sprocket has a 3/8-inch pitch, fits size 35 chains, and is single strand with one set of teeth around its circumference for use with single strand chains. It is a Type B sprocket with a hub projection encircling the bore on ...
1.Brand new and high quality3.Generator Chainsaw Parts, Drum Sprocket - 7 Tooth ( Drum and Bearing are included )4.Fit for STIHL MS360/361/341/362 ChainsawCountry of Manufacture: CHINA; Material: Metal. Net Weight: 172g; Package Content: 1x Sproc...
mpn: 1, ean: 0663591554231,
# 40 Roller Chain A-Plate Sprocket Sprocket Pitch: 1/2 inches（12.7mm) Number of Teeth: 28 Tooth Bore Diameter: 5/8 inches(15.875mm) Outside Diameter: 4.74 inches(120.396mm) Overall Thick:0.275 inches( 7mm) Material: Carbon SteelMaterial:Carbon Stee...
mpn: 513472X, ean: 0036577457404,
POWER MATE SPROCKET SYSTEM...